PM442 Issue 2 (October 2010)IMPORTANTThis appliance will become hot whilst in operation, it is therefore recommended that a suitable guard should be u
107. ASH REMOVAL7.1 Multi-fuel stove Riddle with the tool provided (see Diagram 10).10PR8861Rotate to operate Open Door (see Diagram 11).11PR8729
11 —Fit the plug supplied into the hole where the riddling mechanism is normally located and secure with bolt and clamp (also supplied, se
12 Check that the door shuts properly and creates an effective seal. Leaking door seals prevent the appliance working properly. Do not use aerosol s
1315. CARE OF STOVE Stovax has a range of cleaning and maintenance products and accessories to keep your appliance in good working order. Your Yeoman
1417.5 All or some of the radiators do not get hotBurning wood Wood is burning too slowlyOpen up the airwash to make a hotter fireIf fitted set the t
15TECHNICAL SPECIFICATIONYEOMAN1. STANDARD FEATURES• Primary Air (under grate air for full multi-fuel use).• Airwash (for wood burning / clean glass
16PR8852ADEJFGKCBTECHNICAL SPECIFICATIONDescription A B C D E F (Ø) G H J K L M NYeoman YM-CL8HB563 572 363 105 478 153/6" 449 24 441 225 430 224
171. FLUE OR CHIMNEY1.1 The flue or chimney system must be in good condition. It must be inspected by a competent person and passed for use with the
18150mmminimumConstructional Hearth840mm minimumConstructional Hearth840mm minimum150mmminimum150mmminimum225mmminimumPR8730SITE REQUIREMENTS1. HEARTH
19SITE REQUIREMENTSWALLS NEXT TO A HEARTHPosition of Appliance & Hearth in relation to walls Requirement for the wallsDistance of hearth from wall
2APPLIANCE COMMISSIONING CHECKLIST 3USER INSTRUCTIONS 4General Points 4Using the Appliance for the first time 6Recommended Fuels 6Lighti
20PRE-INSTALLATION CHECKS1. FLUEModelYeoman YM-CL8HBFlue / Chimney Size Without Liner SystemRound (diameter)mm 150inch 6Without Liner System (square)M
212.6 Extractor fans or cooker hoods must not be placed in the same room or space as this can cause the appliance to emit fumes into the room.2.7 In
22LEGAL REQUIREMENTS Before installation and/or use of this appliance please read these instructions carefully to ensure that all requirements are fu
23INSTALLATION INSTRUCTIONS —Secure with self tapping screw. —Seal the connecting joints. Do not use a 90˚elbow to make this connection. The flue
24INSTALLATION INSTRUCTIONS 3. FITTING AND REMOVAL OF THE BAFFLE No tools are required.3.1 To maintain efficient combustion the appliance is fitted
2510PR8875 To remove Multi-fuel frames: —Lift frames from the front. —Remove right hand side first through the front of the stove. —Repeat fo
266.2 Place the cast top plate feet down on top of the appliance. —Ensure the cast top is flush with the front and sides of the appliance. —For the
273. Hot Water Cylinder3.1 The domestic hot water cylinder must be an indirect vented double feed type to meet national standards** and should have a
289. Pump Assisted Central Heating9.1 The most common arrangement is to have a pumped central heating circuit combined with a gravity hot water circu
29INSTALLATION INSTRUCTIONS See below typical layout of a fully pumped central heating and hot water circuit.Feed and Expansion CisternCold Water Stor
3APPLIANCE COMMISSIONING CHECKLISTTo assist us in any guarantee claim please complete the following information:-Retailer appliance was purchased from
30 NOTE - THIS CONDENSATION IS NORMAL DURING FILLING AND DOES NOT INDICATE A FAULTY OR LEAKING STOVE. NORMAL RUNNING1.9 During normal running this
31COMMISSIONING1.1 To commission: — Replace the log retainer. — Check the door alignment and catch operation, adjust if required (see Maintenanc
32MAINTENANCE and SERVICINGFor a complete list of spare parts and accessories contact your Yeoman retailer or call 01392 4740111. ANNUAL SERVICE1.1 B
332. REMOVAL OF THE LOG GUARD2.1 To remove the Log guard: —Lift Log Guard clear of the supporting brackets. —Rotate to clear the sides of the door
34Seal Length (mm)Door rope seal C 2300Door rope seal D 410Mid door rope seal E 450 —Remove the old rope. —Scrape old glue from the locating groove.
35 The hinge plate assembly is slotted so it can be moved up, down and sideways by approximately 3mm to adjust the position of the door in relation t
36SPARE PARTS LISTRef. No.Product CodeDrawing No.(if different) Description1 CA76696” CAST FLUE2 SM13 MEC70046” FLUE BLANKING PLATE3 - ME501805THERMOS
37SPARE PARTS LISTRef. No.Product CodeDrawing No.(if different)Description1 CA7615CAST DOOR2 MEC8619DOOR HANDLE ASSEMBLY3 FA500024WAVE SPRING - YRW-00
SERVICE RECORDS381ST SERVICEDate of Service:...Next Service Due:...
A division of Stovax LtdFalcon Road, Sowton Industrial Estate, Exeter, Devon, England EX2 7LFTel: (01392) 474500 Fax: (01392) 219932E-mail: yeoman@s
4USER INSTRUCTIONS1. GENERAL POINTS1.1 Before use of this appliance please read these instructions fully. The appliance must be fitted by a registe
5USER INSTRUCTIONS2PR8857 For Air Controls see the diagram over. Use the tool provided to operate the air controls. Do not place tool on hot surfac
6USER INSTRUCTIONSWARNING Properly installed, operated and maintained this appliance will not emit fumes into the room. Occasional fumes from de-ashi
7USER INSTRUCTIONS5 —Leave the door slightly open as the fire establishes and the glass warms to avoid the build-up of condensation. —Add large
8USER INSTRUCTIONS5. RUNNING THE APPLIANCEBURNING WOOD:5.1 This appliance gives out its heat in two ways: —Directly into the room in which it is fit
95.8 De-ash the firebed before re-fuelling (see User Instructions, Section 7). Open the Primary Air Control fully to establish a glowing bed before
Comments to this Manuals