Yeoman YM-CL8HB User Manual download pdf (Page 9)

5.8 De-ash the firebed before re-fuelling (see User

Instructions, Section 7).

Open the Primary Air Control fully to establish a glowing

bed before adding new fuel.

Burn new fuel at a high temperature (see Diagram 7) for a

few minutes before adjusting the Primary Air Control to

the desired setting.

Refuel little and often for clean, efficient burning.

5.9 Experience establishes settings to suit personal preference.

5.10 Do not burn large amounts of fuel with the Primary Air

Control on a low combustion setting for long periods of

time. This reduces the glass cleaning effect of the Airwash

and causes tars and creosotes to build-up in the appliance

and flue system.

5.11 When in use, burning the appliance at a high temperature

for a short period reduces tars and creosotes.

5.12 Only anthracite or smokeless fuels suitable for use in

closed appliances must be burned in this appliance.

5.13 Do not burn bituminous coal, ‘petro-coke’ or other

petroleum based fuels as this invalidates the product

guarantee.

5.14 Do not load fuel above the log guard and the base of

the baffle at the back of the firebox (see Diagram 5).

REFUELLING

5.15 De-ash the fire bed before refuelling, see Ash Removal

—Open the Primary air control fully to establish a

glowing bed before adding new fuel.

—Do not refuel when a large amount of flame is

present in the firebox as this could cause smoke or

flames to spill into the room.

—Close the doors immediately after refuelling.

—Burn new fuel at a high temperature for a few minutes

before adjusting the Primary air control to the desired

setting.

—Refuel little and often for clean, efficient burning.

5.16 Do not re-fuel the stove above the level of the log guard

or the base of the baffle.

THERMOSTAT OPERATION

5.17 This appliance can be fitted with a thermostat kit to

control the temperature of the boiler. See the instructions

included in the kit for operation details.

USER INSTRUCTIONS

6. BURNING TIPS

6.1 Fuel Quality (Wood)

Use wood with a moisture content of less than 20%.

Seasoned logs have the bark beginning to lift and peel away

and cracks radiating from the centre. They feel lighter than

fresh cut wood of a similar size and sound hollow when

struck against each other. Logs should not feel damp or

have moss and fungal growths.

Symptoms related to wet wood:

—Difficulty starting and keeping a fire burning well.

—Smoke and small flames.

—Dirty glass.

—Rapid creosote build-up in the chimney.

—Low heat output.

—Short burn times, excessive fuel consumption and

blue/grey smoke from the chimney.

Burn at a high temperature for a short period each day

to avoid large build-ups of tars and creosote within the

appliance and the flue system.

Use Stovax Protector chimney cleaner to reduce this

problem.

6.2 Fuel Quality (Solid Fuel)

Use recommended solid fuels approved for use with closed

appliances.

Symptoms related to unsuitable fuels include:

—Difficulty starting and keeping a fire burning well.

—Smoke and small flames.

—Dirty glass and/or fire bricks.

—Short life span for Grate and Baffle.

—Permanent staining of glass.

6.3 Air inlets puffing smoke

Combustion gases can build up in the firebox and ignite

as small explosions, causing smoke to puff out of the air

inlets and other openings. This occurs if the air controls

are shut soon after adding new fuel to a very hot fire. Stop

by opening the air controls to increase combustion air and

burning rate.

6.4 Flue Draught

The chimney has two main functions:

1) To safely remove the smoke, gases and fumes from the

house.

2) To provide a sufficient amount of draught (suction) in the

appliance ensuring the fire keeps burning.

In the U.K.

* Registered on the Competent Persons Scheme (GB only)

see page 35 / INFO (Republic of Ireland).

** This should be done by a HETAS registered chimney

sweep, see page 35, who will issue you with a certificate.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 38 39

Comments to this Manuals

No comments

Yeoman YM-CL8HB User Manual Page 9

Comments to this Manuals